正常焊接英语怎么说及英文单词

㈠ 关于焊接的所有英语词汇

《焊接词典》。机械工业出版社。含所有的焊接名词，并有英文对照。

㈡ 谁能帮忙翻译几个英语单词啊 “焊接 电子产品 电烙铁 工艺质量” 谢谢

焊接：welding
电子产品：electronic procts
电烙铁：electric soldering iron
工艺质量：process quality

保证准确

㈢ 求焊接英语文摘

焊接类英语文章阅读

Tapping the Low Hydrogen Porosity Problem

Tapping the Low Hydrogen Porosity Problem
By Dan Mahony, Technical Salesman, and Paul Gramp, Distributor Trainer, The Lincoln Electric Company.

Stick Welding Porosity in a weld is considered poor quality. Porosity may, or may not, be visible to the naked eye. Occasionally porosity can be found in the face of the weld while sometimes the face may appear porosity free, but deep inside the weld, porosity may exist. Porosity looks "sponge like" or like tiny bubbles in the weld. Porosity in a weld can be located using several different methods of non-destructive testing, such as radiographic (x-ray), UT (ultrasonic) and die penetrate.

"...strike the arc, then lift the electrode up for a moment or two, allowing a few drops of electrode to fall from the tip."

Although some porosity found at the beginning of a weld made with low hydrogen electrodes is not always apparent, it is possible and the solution itself may be simple. Often, even with an experienced welder, weld testing will show slight porosity at the beginning of a weld for no apparent reason. Porosity is often found when using low-hydrogen electrodes such as E-7018, and it may be difficult to establish why this occurs.

Stick Welding In order to understand the real cause, it is necessary to look at the way stick electrodes are manufactured, as well as how they are used in the field. The steel core wire, as we know, concts electrical current from the electrode holder to the work . It also melts to become the filler metal. The chemical coating that forms the flux layer is extruded on to the steel core wire and baked in a controlled oven to remove moisture. The flux coatings major task is to vaporize and form a shielding gas to protect the weld puddle from nitrogen, hydrogen and oxygen.

During manufacturing, after the coating is applied and it is still soft and pliable, a set of brushes removes coating to accommodate the electrode holder. Another set of brushes slightly tapers the work end of the electrode to expose the end of the steel core wire. This exposed end allows a short circuit to be established when it touches the work at the start of the weld. As the weld progresses, the steel wire burns slightly up inside the flux (approximately 1/8 of an inch), so the coating melts to form the necessary shielding gas. Striking a new electrode, however, the tapered coating at the end of the electrode provides only minimal shielding since some of the coating was intentionally removed to accommodate easier arc starting. Therefore, if the operator lowers the electrode into the puddle immediately, some porosity may result at the beginning of the weld, which is caused by insufficient amount of coating on the steel core wire.

This condition also exists when re-striking an electrode that has already been used. Before striking an arc, the welder frequently taps the end of the electrode on the ground to break away flux at the tip. Breaking away the flux to expose the steel core wire, while helping to achieve the short circuit necessary to start the arc, creates conditions for improper arc shielding, sometimes resulting in porosity at the start of the weld. This practice is much more common with low hydrogen electrodes, since the core wire melts up inside the flux coating. Electrodes such as E-6010 and E-6011 use organic coatings (paper), which the coating tends to burn back enough to leave the end of the core wire exposed.

Stick WeldingThis type of porosity can be avoided if the operator is trained to strike the arc correctly. Immediately after establishing the arc, lift the electrode up a short distance from the work and holding it there for a second or two, allow a few drops of molten steel to fall from the tip of the electrode. The arc will bring the tip of the electrode up to operating temperature quickly, enabling the core wire to burn up inside the flux coating and initiate the gassing effect of the flux. Then, when the electrode is lowered to the work, the weld will be properly shielded, and porosity will be minimized.

Proper training is always important to achieving good results in welding. Training is even more critical when dealing with low hydrogen electrodes. A little understanding of how these electrodes differ and the consequences of improper electrode handling will pay big dividends in better weld quality and fewer porosity defects.

参考资料：http://www.jxcad.com.cn/read-htm-tid-208667.html

网络上搜焊接英语文章，有很多资源的

㈣ 焊道的英文单词是什么

bead

㈤ 免焊和焊接的英文怎么怎么说啊

您的问题很简单。呵呵。网络知道很高兴帮助您解决您提出的问题。
原句：免焊
翻译： solder-free
焊接：weld；soldering；seal；sealing-in

免清洗焊膏：no-clean solder paste
自动焊接[机] automatic welding；AW；Welding automatic；tape automated bonding
焊接冶金Welding Metallurgy；weld metallurgy
焊接管[机] welded pipe；[机] welded tube；[机] welding pipe；welding-machine
焊接螺帽WELD NUTS
焊接方向welding direction；direction of welding；welding progress
焊接应力welding stress；weld stress；stress of welding
焊接温度welding temperature；soldering temperature；Lead Soldering Temperature；Solder temperature
焊接裂纹weld crack；welding crack；welded fissure；weld flaw
感应焊接inction welding；Inction soldering

网络知道永远给您最专业的英语翻译。

㈥ 焊接英语翻译一句话答对高分

Weld plans did not note the tag, in addition to similar conditions, as appropriate, welding, welding high are welded pieces of mother-thin 0.7 t angle for the Weld

㈦ 求翻译焊接专业英语词汇！！！急急急~~~~~

针状亚铁盐抄 ,谷粒边界亚铁盐,多角袭形的亚铁盐,和第二的时期亚铁盐不排列,和被排列的第二时期，和第二的时期亚铁盐，之前的沃斯田铁谷粒宽度的亚铁盐。
ferritic 所有的-焊接处-金属， charpy v- 刻痕测试,vickers 坚硬,圆柱的地域。

㈧ 焊接专业英语 翻译

proportions of welded joints have been standardized. preferred sizes, dimensions ,and charts
焊缝抄的袭比例已经标准化。用于计算焊缝所需的焊接材料的强度及用量
for calculating the strengths of and amounts of filler metal required for welded joints are given in reference texts and handbooks
的最佳的大小，尺寸及外观已经在参考资料及手册中给出。
4.the base metal
母材
5.polarity switch
极性转换
6.not shortness
非短缺
7.slag inlusion
夹渣
8.positional welding
定位焊
9.the welding zone
焊接区
13.types of welds
焊接类型
15.the ground clamp cable
地线夹
16the weldability of metals
材料的可焊接性

㈨ 有关焊机的英语单词，请高手帮忙

根据来题，按照顺序回答如下：
1. INVERTER DC ARC: 逆变式直流弧焊
2. INVERTER AC/DC TIG: 是逆专变式交流/直流钨极属氩弧焊
3. INVERTER DC TIG: 是逆变式直流钨极氩弧焊
4. INVERTER AIR PLASMA CUTTER: 是逆变式空气等离子切割机
5. INVERTER CO2 MAG: 是逆变式二氧化碳气体保护焊