漏检故障英语怎么说及英文翻译
A. 故障图的英文，故障图的翻译，怎么用英语翻译故障图
fault-graph ； trouble chart.
A basic problem abstracted from fault-graph is studied. 研究内容是在系统故障图分析中抽象出的一个内基础问容题。
B. 发生故障的英文，发生故障的翻译，怎么用英语翻译发生
break down
be out of order
go wrong
亲：祝你学习进步，每天都开心V_V！
望采纳，thx!
Mr Gao
C. 常见故障及处理方法用英语怎么说
常见故障及抄处理方法袭的英文翻译_
Common
faults
and
treatment
methods
方法
[名]
method;
way;
means;
technique;
measure;
[例句]摆脱这一困境的方法尚未找到。
A
way
out
of
the
difficulty
has
not
yet
to
be
found.
D. 请高手帮忙翻译一句英文：请提供本次维修的报告，报告内容包含故障现象以及故障原因。谢谢！
Please provide the maintenance that reported the content includes fault phenomena and breakdown reason.
E. 漏检错误率英文怎么写
漏检错误率
resial error rate
undetected error rate
MAC服务为发送数据包引入了非常低的漏回检错误率。答
The MAC Service introces a very low undetected frame error rate in transmitted frames.
F. 这项故障报告还未提交,请您及时提交,谢谢怎么翻译成英语
这项故障报告还未提交,请您及时提交专,谢谢。
The failure report has not been submitted, please submit in time, thank you.
求采纳属
G. 英语翻译(汽车故障报警)
你这个是英语
法语是:PILE PLIP USAGEE
意思是手持式遥控器电池电量不足
H. 请问“故障诊断”英文怎么翻译
breakdown diagnosis
I. 求高手翻译成英文啊~~不良对策报告，谢谢！翻的好可以追分！ 可以发到我邮箱 [email protected]
1）C/L偏移：
1) C/L migration:
1、客户图纸上面焊盘部位长度没有数据，数据测量时没有进行管控;
1 and customer's drawing pad parts above length no data, data measured not control;
2、覆盖膜开窗是切割机切割出来，切割窗口完成后需要进行二钻定位孔，二钻定位孔是切割出来，切割时定位孔容易出现撕裂或者不圆等现象，贴附时导致覆盖膜定位孔对制品孔对不齐，导致开窗偏移，即出现C/L偏移。
2, covering membrane window is cutting machine cutting out after completion, cutting window need for two, two drill holes drilled positioning is cutting out, positioning hole ring cutting positioning hole prone to rent or not round etc. Phenomenon, attached with a lead to coverage of membrane positioning hole to not neat, procts hole that led to open the window migration, appear C/L migration.
2）短路：
2) short-circuit:
1. 打样时因数量少作业员手工开料，由于基材薄，开料后产品有些折皱，导致曝光时出现曝光不良，DES后形成短路现象。
1. When less homework because of quantity salesman manual opens the material, because members backing thin, opens the material procts, leading to expose some wrinkles appear after exposure bad, DES formed short-circuit phenomenon.
2.样品打样交期紧，当时测试治具没有制作回来，所以敝司暂定要求FQC检验员在40X显微镜下对线路进行100%开短路检验，因检查员不仔细未发现导致不良漏检流出
2. Sample proofing delivery tight, then test fixture did not make back, so our company 40X provisionally requirements under microscope in FQC inspectors to open the lines, for 100% short-circuit test that causes not carefully inspectors, adverse undetection outflow
3. 流出原因：
3. Outflows reasons:
检查员不仔细未发现导致不良漏检流出。
Inspector without careful not found that lead to bad undetection outflow.
4. 发生对策 ：
4. Happen countermeasures:
1）C/L偏移：
1) C/L migration:
1.发现覆盖膜开窗偏移大的产品需要测数确认，超出公差范围的产品报废处理；
1. Find insium window offset big procts need to test several confirmation, beyond the tolerances procts rejected processing;
2.量产时开钢模可以完全避免此现象发生。
2. When open mass proction to completely avoid the steel mold phenomenon.
2)短路：
2) short-circuit:
1.对开料工序作出要求，样品无论数量多少，都要使用机器开料，确保基材平整度。
1. Commuting requirements, material process make sample regardless of the quantity, want to use the machine to ensure open material base material smoothness.
2. 电测治具已经OK，量产时通过电测治具对开短路进行测试，可以彻底避免此不良流出；
2. Electrical measurement fixture has OK, mass proction by electrical measurement when opening fixture short-circuit test, can completely avoid the bad outflow;
5.流出对策：
5. Outflows countermeasures:
1. 客诉不良对FQC检验员进行培训，同时后续所有的样品检查FQC固定2人专门对应。
1. Poor aftersale inspectors to FQC trained, and subsequent all samples check FQC 2 special fixed position.