回轉水平儀英語怎麼說及英文翻譯

Ⅰ 「 水平」的英文怎麼說

您好，領學網為您解答：
水平[shuǐ píng] level; horizontal; standard; plane
level 英 [ˈlevl] 美 [ˈlɛvəl] n.水平，水準;水平線，水平面;水平儀;[物]電平 adj.水平的;同高度的;平均的;平穩的 vt.使同等;對准;弄平 vi.拉平;（用槍等）瞄準（與 at 連用）;變得平坦;將（話、批評等）對准目標 vi.瞄準;拉平;變得平坦
horizontal 英 [ˌhɒrɪˈzɒntl] 美 [ˌhɔ:rəˈzɑ:ntl] adj.水平的，卧式的;地平線的;[植]（枝條）平層的;同一行業的，同階層的 n.水平線;水平面;水平位置;水平的物體
standard 英 [ˈstændəd] 美 [ˈstændərd] n.標准，規格;旗，軍旗;度量衡標准;直立支柱 adj.標準的，合格的;普遍的，一般的;公認為優秀的
plane 英 [pleɪn] 美 [plen] n.平面;飛機;水平;木工刨 adj.平的，平坦的 vt.用刨刨平;小船等擦著水面疾駛 vi.鳥滑翔
望採納！

Ⅱ 英語高手請進,翻譯下衣服上的英文

LEVEL 水平
BY MIND 我的思想
S.O.S 國際通用的呼救信號第二件
BENT ON 決心做某事的
PLEASING YOU 「PLEASING」表示令人喜愛的，表示取悅你。
都沒有不雅的意思，樓主可以放心

Ⅲ 水平儀上是TONGCHANG字母是什麼牌子的水平儀

水平儀上是這組英文字母，它的牌子應該就是。各地的水平儀牌子的。

Ⅳ 英語翻譯，這里的level在這里是什麼意思呢

沒看到有問題

Ⅳ 這是什麼這是一個水平儀。求英文翻譯

what is this? It is a gradienter.

Ⅵ 請各位英語達人幫忙翻譯啊 謝謝了~~翻譯成英文

4. 安裝與調整
4.1 安裝：
環境要求：端面銑床安裝在乾燥無粉塵、無腐蝕性氣體的溫度在10～40℃的室內堅硬水泥地面上。
4.1.1 調平：機床到位後用水平儀置於工作檯面調整端面銑床底面的四個調整座，直到調整水平不超過0.5/1000的位置，然後鎖緊調平螺母。
4.1.2 接地：必須按電器接線圖要求接地線，其規格截面積大於2.5mm2的軟銅芯和綠黃組合顏色的絕緣線，接地電阻不大於4歐姆。
4.1.3接氣：工作氣壓為0.5～0.8MPa，耗氣量100L/min，將氣源接在氣源處理器的接頭上，檢查各氣路有無漏氣現象。
4.2 調整
4.2.1 夾緊缸的調整：首先松開氣缸夾持板上的緊固手柄，將氣缸調整到一個能夠適應加工型材壓緊的合適位置，調整好壓頭，使其不至碰到定位板。
4.2.2 工作台角度的調整，如需銑削有角度型材，可首先松開定位板下的緊固手柄，撥出定位銷，然後將定位板調整到（左55°右55°）適合的范圍內，將緊固手柄緊固好。
4.2.3 銑削速度的調整氣動原理圖
可通過調整氣缸上的單向節流閥，以達到進給和後退的合適的速度。（可根據型材質量調整速度快慢）
4.2.4 工件銑削深度的調整
工作銑削深度的調整，可通過調整定位塊的位置以達到銑削深度的目的。
4.2.5 電動機的縱向行程的調整：電機的縱向調整也就是銑刀銑削工件（型材）位置的調整。可通過調整定向手柄下方的調整螺母來實現，順時針方向，電機上升，反之，則下降，調整好位置後，將機箱兩側的五角星型手柄鎖緊。
4.2.6 噴霧量大小的調整：調節噴霧量的大小可旋轉閥門開關，改變噴灑面的大小。
4.2.7 工作台的調整：在銑削時橫向進刀是為了達到工件（型材）銑削需要。
5. 使用與操作
4. Installation and adjustment

4.1 installation:

Environmental Requirements: End-milling machine installed in the dry st-free, non-corrosive gases in the temperature 10 ~ 40 ℃ hard indoor concrete floor surface.

4.1.1 Leveling: Machine Level in place after the work under the table to adjust the bottom end of the four adjustment milling Block until the adjustment of the level of not more than 0.5/1000 position, and then locking nut leveling.

4.1.2 Ground: must be in accordance with the requirements of electrical wiring diagram grounding line is greater than its cross-sectional area of 2.5mm2 specification of the soft copper color to green-yellow combination of insulated wire, grounding resistance not more than 4 ohms.

Coherent 4.1.3: Working pressure of 0.5 ~ 0.8MPa, consumption 100L/min, the gas source then the source of the gas connector on the processor to check whether the gas leak phenomenon.

4.2 adjustment

4.2.1 clamping cylinder adjustment: First release of the fastening plate cylinder gripping the handle, the cylinder was adjusted to a compact profile to adapt to the appropriate processing location, adjusting the pressure head, so that it does not to touch to the positioning plate.

4.2.2 table angle adjustment for angle milling profiles, be the first release of the fastening plate positioning handle pin set aside, and then adjust the positioning plate to (left 55 ° right 55 °) for the the scope will be good fastening fastening handle.

4.2.3 Milling adjust the speed of pneumatic schematic

Cylinder can be adjusted on a one-way throttle valve in order to achieve back-feed and the appropriate speed. (Which can be adjusted in accordance with the quality of speed profiles)

4.2.4 Milling depth adjustment of the workpiece

Milling depth adjustment work can be targeted by adjusting the location of block in order to achieve the purpose of milling depth.

4.2.5 motors to adjust the vertical journey: the vertical adjustment of motor is the milling cutter workpiece (Profile) position adjustment. May be directed by adjusting the adjusting nut under the handle to achieve, a clockwise direction, the electrical rise, on the contrary, there was a decrease, adjusting the location of a good will on both sides of the five-pointed star-type chassis locking handle.

4.2.6 the size of the adjustment of spray volume: adjust the size of the volume of spray valve can rotate to change the size of sprayed surface.

4.2.7 table adjustment: when in the horizontal feed milling in order to achieve the workpiece (profile) milling needs.

5. The use and operation of

Ⅶ 鋼琴十級水平 用英語怎麼說

Piano Level 10

詞彙分析：

piano

英 [piˈænəʊ , ˈpjɑːnəʊ] 美 [piˈænoʊ , ˈpjɑːnoʊ]

n.鋼琴

adv.輕柔地;安靜地;弱

復數： pianos

派生詞： piano

我自學了彈鋼琴。

(7)回轉水平儀英語怎麼說及英文翻譯擴展閱讀：

類似詞語：小提琴十級水平：Violin Level 10

詞彙分析：

violin

英 [ˌvaɪəˈlɪn] 美 [ˌvaɪəˈlɪn]

n.小提琴

復數： violins

Lizzieusedtoplaytheviolin.

莉齊曾經拉過小提琴。

Ⅷ 水平尺、水準儀、經緯儀、鋼捲尺、全站儀的英語怎麼讀是要那種最准確的讀法

水平尺：track level bar
水準儀：level
鋼捲尺：steel measuring tape
全站儀：total station或electronic tachometer(即電子速測儀）

sfaff不知道啥意思，不過staff是標尺的意思。
另外，水準尺：leveling staff

Ⅸ 攝影器材產品英文翻譯

1. Photographic slide rail with high precision level meter, through observation level instrument inside bubbles so far can be judged is placed in a horizontal position (bubble in the middle of the circle said the instrument in a horizontal position, or does not reach the level)
2 the outside of the slider without manual damping, elastic random adjustment, the adjustment is loose, the slider is smoother. Using CNC precision machining process, more rable, and has a stronger ability to lock
3 the new sliding block panel is designed, and provided with a plurality of screw holes, other equipment and equipment can be installed, and the panel is provided with a circular shock proof device. Let your shooting equipment can be set at ease. Don't fear any bumps
4 relying on the leading technology, the use of widely used in aerospace, the cause of the defense force of the carbon fiber material, eight layers of carbon fiber tube, bearing large. Light weight
The 5 supporting legs can be folded directly, and the utility model can be used in multiple angles, and the utility model can be conveniently and quickly used.

Ⅹ 水平儀的英語翻譯 水平儀用英語怎麼說

水平儀
[詞典] level; gradienter; [機] air level; level via